1998 civic viper 5701

1998 Civic Lx (4 doors) Automatic Viper 5701 USED THIS DIAGRAM Connection: *Primary(h1) 12-pin H1/1 RED / WHITE           (-) 200mA TRUNK RELEASE OUTPUT        not used H1/2 RED        (+)12v CONSTANT INPUT              White        H1/3 BROWN   (+) SIREN OUTPUT            red on siren ( grounded black to chassi of car) H1/4 WHITE/ BROWN    LIGHT FLASH -ISOLATION WIRE   not used H1/5 BLACK     (-) CHASSIS GROUND              chassis ground H1/6 VIOLET    (+) DOOR TRIGGER INPUT             not used i mine is (-) H1/7 BLUE        (-) TRUNK PIN/ INSTANT TRIGGER INPUT     Radio Light Green (-) H1/8 GREEN     (-) DOOR TRIGGER INPUT        Light GREEN/ Red (-) H1/9 BLACK/ WHITE       (-) 200mA DOME LIGHT OUTPUT            lt green /black factory alarm plug H1/10 WHITE/ BLUE        (-) REMOTE START/ TURBO TIMER ACTIVATION INPUT not used H1/11 WHITE   PARKING LIGHT OUTPUT     not used turned off in settings H1/12 ORANGE             (-) 500mA GROUND WHEN ARMED OUTPUT   not used *Auxilary harness (H2) 8 pin   **DIDNT USE ANY*** H2/1     LIGHT GREEN/ BLACK H2/2     LIGHT GREEN/ WHITE H2/3     WHITE/ VIOLET H2/4     VIOLET/BLACK H2/5     WHITE/ BLACK H2/6     LIGHT BLUE H2/7     GRAY/BLACK H2/8     BROWN / BLACK (-) 200mA FACTORY ALARM DISARM OUTPUT (-) 200mA FACTORY ALARM ARM OUTPUT (-) 200mA AUX 1 OUTPUT (-) 200mA AUX 2 OUTPUT (-) 200mA AUX 3 OUTPUT (-) 200mA 2ND UNLOCK OUTPUT (-) DIESEL WAIT TO START INPUT (-) 200mA HORN HONK OUTPUT Door lock harness 3 pin 1 Blue + lock       GREEN / WHITE   driver kick blue plug ( source of wire color direct wire) 3 green - unlock    GREEN/ orange driver kick blue plug ( source of wire color direct wire) *Heavy Gauge remote start (h3) 1   PINK              (+) IGNITION 1 INPUT/OUTPUT      Ignition     BLACK / YELLOW 2   RED / WHITE (30A) FUSED IGNITION 2 / FLEX RELAY INPUT 87      Constant 12V+     White 3   ORANGE       ACCESSORY OUTPUT             Accessory                WHITE/ Black 4   VIOLET          (+) STARTER OUTPUT (CAR SIDE OF THE STARTER KILL WIRE)      Starter     BLACK/ White 5   GREEN           (+) STARTER INPUT (KEY SIDE OF THE STARTER KILL WIRE)   Starter     BLACK/ White 6   RED(+) FUSED (30A) IGNITION 1 INPUT              Constant 12V+     White 7 PINK/WHITE   (+) IGNITION 2 / FLEX RELAY OUTPUT      Ignition 2     Yellow   programed in settings as ignition 2 8 PINK/BLACK    FLEX RELAY INPUT 87A key side (if required) of FLEX RELAY      not used 9 RED / BLACK      FUSED (30A) ACCESSORY/STARTER INPUT       Constant 12V+     White *Remote start input 5 pin* 1   BLACK/ WHITE   (-) NEUTRAL SAFETY SWITCH INPUT    connected to wire h1/5 which goes to chassis 2   VIOLET/WHITE     TACHOMETER INPUT WIRE    blue wire behind tach that read voltage when tach worked and when i disconected it tachometer stoped working 3    BROWN              (+) BRAKE SHUTDOWN WIRE     GREEN / WHITE brake switch 4    GRAY   N/O or N/C (-) HOOD PIN SWITCH INPUT, ZONE 6      to hood pin 5 BLUE/WHITE              (-) 200 mA 2ND STATUS/REAR DEFOGGER    not used Remote start aux output 5 pin **didnt not use any Note: Wires 1 - 4 on the remote auxiliary outputs are wired to the (-) triggers for the onboard remote start relays and are not diode isolated. If wiring these wires directly to the vehicle you must place a 1-amp diode in line to prevent feedback from the vehicle. 1 PINK/WHITE (-) 200mA FLEX RELAY CONTROL OUTPUT 2 ORANGE (-) 200mA ACCESSORY OUTPUT 3 VIOLET (-) 200mA STARTER OUTPUT 4 PINK (-) 200mA IGNITION 1 OUTPUT 5 BLUE (-) 200mA STATUS OUTPUT My question: car does remote starts, remote shuts off , alarm works , doors unlock ,locks . Only thing 2 way remote doesnt show confirmation. when i press something   like lock ,it locks the car but gives me at first F led solid and orange led flashes then in few seconds beeps 2 times with F led 4 times like: ty dy ....few seconds pause ty dy ....pause .... ty dy....pause ... ty dy also when i unlock siren chirps twice then in few seconds one more chirp . when i lock only once.    Please help . USED THIS DIAGRAM

reset the brain by removing all fuses for 30 seconds.

Ted

2nd Year Tier 1 Medical School

Still installing as a hobby...pays for groceries

Compustar Expert

tedmond wrote: reset the brain by removing all fuses for 30 seconds.

just did it tried twice first 30 sec , 2nd time 1 min , same no change :(   ( also bought new battery for remote.

you most likely have a defective remote then.

i ran into the same problem awhile back, had to buy new remotes

Ted

2nd Year Tier 1 Medical School

Still installing as a hobby...pays for groceries

Compustar Expert

tedmond wrote: you most likely have a defective remote then. i ran into the same problem awhile back, had to buy new remotes

Ill try new remote at the end of week. How does the wiring look? Any wire that needs to be connected? I really appreciate your time.

any body else had /have this issue ?   thxz

wiring looks fine.

there were many issues with remotes not working, did you buy the unit online?

Ted

2nd Year Tier 1 Medical School

Still installing as a hobby...pays for groceries

Compustar Expert

Yes, but its covered under lifitime no hassle exchange.

I'm shipping the brain and remotes for testing and exchange, ill post back with results.

Out of the 20 or so 5301 and 5701 that I have dealt with, I had one that acted the way yours does.   No matter what I tried, it remained funky.  Replace it.When all else fails, Read the Instructions

Support the12volt.com Make a Donation