viper 5101 8 pin connector

Home / the12volt's Install Bay / Car Security and Convenience / viper 5101 8 pin connector (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

shafferny

Copper - Posts: 240

Joined: February 02, 2008

Location: New York, United States

Posted: January 31, 2010 at 6:50 AM / IP Logged

I just purchase a Viper 5101 to go into my 2003 Jeep Liberty. The installation manual is a bit vague when it comes to the H3 connector, or "Heavy guage, 8-pin connector". Can anybody tell me what the characteristics of the wires I need to connect these to are? For example:

H3/1

PINK

IGNITION 1 INPUT/OUTPUT

Needs to be connected to a constant 12v in the ignition harness.

TIA,

Chris

Without the garble. ;-)

shafferny

Copper - Posts: 240

Joined: February 02, 2008

Location: New York, United States

Posted: January 31, 2010 at 11:43 AM / IP Logged

When I installed previous remote starters made by Design Tech, the instructions would give directions such as....

4. Blue Wire (14 AWG) – Ignition 1

Connect the BLUE wire to the ignition 1 wire of your vehicle. This wire will measure

+12 Volts on the test meter in the “run” and “start” position, and is off in the “lock/

off” and “accessory” positions

It made find the correct wires accurate and easy.

I emailed DEI and the website I purchase the remote car starter to see if I could get a vehicle specific wiring diagram, but I'm not sure if I'll get a satisfactory response. As most of you know, DEI's website is useless to the DIY installer. It's geared soley for the end user and professional installer/authorized dealer.

tedmond

Gold - Posts: 4,610

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: January 06, 2007

Location: Ontario, Canada

Posted: January 31, 2010 at 11:50 AM / IP Logged

connect that pink H3/1 to RED / BLUE (+) @ ignition harness.

Ted

2nd Year Tier 1 Medical School

Still installing as a hobby...pays for groceries

Compustar Expert

t&t tech

Platinum - Posts: 2,608

Joined: October 05, 2008

Location: Trinidad and Tobago

Posted: January 31, 2010 at 1:01 PM / IP Logged

To expand on ted's post

Green- starter wire (key side)

Purple- starter wire (engine side)

orange - acesory

pink/white second ignition

all the reds to 12volts constant

commit your way to jehovah and he will act in your behalf. psalms 37:5

shafferny

Copper - Posts: 240

Joined: February 02, 2008

Location: New York, United States

Posted: January 31, 2010 at 1:12 PM / IP Logged

Is this correct for the H3 harness?

H3/1(Pink) ->RED / Blue @ Ignition Harness

H3/2(RED / White) ->N/A

H3/3(Orange) ->BLACK/ Orange @ Ignition Harness

H3/4(Violet) ->Yellow @ Ignition Harness

H3/5(Red) ->Unsure (Red & Pink/Black @ Ignition Harness)??

H3/6(Pink/White) ->N/A

H3/7(Pink/Black) ->N/A

H3/8 ->Unsure (possibly BLACK/ White @ Ignition Harness)??

shafferny

Copper - Posts: 240

Joined: February 02, 2008

Location: New York, United States

Posted: January 31, 2010 at 2:49 PM / IP Logged

I appoligize if I'm being ignorante here, but I don't see a green wire at all in the harness.

Page 24 of the PDF below are the wires I'm trying to figure out. The instuctions aren't clear at all.

http://www.directeddealers.com/manuals/IG/Viper/N4102V_2008_09_web.pdf

Here are is the vehicle wiring chart I received from Direct back in 2007 when I installed the current remote car starter.

viper 5101 8 pin connector -- posted image.

t&t tech

Platinum - Posts: 2,608

Joined: October 05, 2008

Location: Trinidad and Tobago

Posted: January 31, 2010 at 2:59 PM / IP Logged

That unit may not have the starter kill/anti grind then, Ignore the green wire then, connect the purple to the yellow!

RED / white and red go to pink/black in the ignition harness!

commit your way to jehovah and he will act in your behalf. psalms 37:5

shafferny

Copper - Posts: 240

Joined: February 02, 2008

Location: New York, United States

Posted: January 31, 2010 at 3:21 PM / IP Logged

The anti-grind feature is optional.

H3/1(Pink) ->RED / Blue @ Ignition Harness

H3/2(RED / White) ->(Red & Pink/Black @ Ignition Harness)

H3/3(Orange) ->BLACK/ Orange @ Ignition Harness

H3/4(Violet) ->Yellow @ Ignition Harness

H3/5(Red) ->N/A

H3/6(Pink/White) ->N/A

H3/7(Pink/Black) ->N/A

H3/8 ->Unsure (possibly BLACK/ White @ Ignition Harness)??

shafferny

Copper - Posts: 240

Joined: February 02, 2008

Location: New York, United States

Posted: February 01, 2010 at 5:06 PM / IP Logged

Can anybody confirm this?

I contacted the retailer I purchased the remote starter from, Dealer Cost Car Audio, and they wouldn't provide me with any information because they didn't want to be held liable for anything.

This is frustrating to say the least.

t&t tech

Platinum - Posts: 2,608

Joined: October 05, 2008

Location: Trinidad and Tobago

Posted: February 01, 2010 at 5:51 PM / IP Logged

All is correct above, except the red h3/5 connects with the RED / white at either of the twelve volt constant wires at the harness! What colour is your h3/8 wire?

commit your way to jehovah and he will act in your behalf. psalms 37:5

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.